Jump to content

Jamief's Splicédex - 2 entries.


jamief

Recommended Posts

Well it's been a while since i made any Splices, and now i'm back into it. So i'm deciding to make a Pokedex consisting of only recolours and splices of mine. Enjoy.

 

[spoiler=Dark Moltres - #001]

 

6fb8d0.png1zwz2gz.png

 

[spoiler=Splicédex Entry]

 

Type: Dark / Fire

Evoloution: Evolves from Moltres with Evil Stone

Height: 6'7"

Weight: 132 lb

 

Entry: This Legendary Bird is formed when Moltres is united with a Evil Stone.

 

 

 

 

 

[spoiler=Manectrium - #002]

 

358dpxx.png

 

[spoiler=Splicédex Entry]

 

Type: Grass / Electric

Evoloution:

Height: 6'10"

Weight: 88.3 lbs

 

Entry: This Rare Fusion Pokemon was found and rescued from Team Rockets Lab. It quickly bred upping the population to only 73.

 

 

 

 

 

[spoiler=Green Starmie - #003]

 

2drevef.png

 

[spoiler=Splicédex Entry]

 

Type: Grass / Water

Evoloution: Evovlves from Staryu with Leaf Stone

Height: 3'7"

Weight: 176 lbs

 

Entry: Hides at the bottom of the Ocean inside the Seaweed. Very rarely seen.

 

 

 

 

 

 

 

 

Splicédex Completion: 2/56

Link to comment
Share on other sites

Well like I say much, much, much, much, much, much, much, much, much too often, you neglected to recolor the borders. If you don't do that, you're splices and recolors will look very unprofesional and bad. If you don't know what I'm talking about, take a close look at the sprite, see on moltress those borders that are brown. Those should have been made into a dark gray color. Now that's out of the way, I can move on.

 

Moltres other than the border issue is fine, I see nothing overly wrong with it. The female's beak and claws could be a tad dark, they seem a little too pale, darken up that second shade a tad.

 

THe splice firstly is too simple. A simple adition of its head and tail seems all you did. The head also isn't in there pefectly, could be a good bit better. Those border issues also remain in this one, and seem all over the place.

 

Ugg, the Starmie seems so bad. Not only because of the border, but the color choice with it. That green is a really pale, and doesn't go well with all those left over blue and purple bits. It might be better if it didn't have those.

 

Pay attention to those borders and take your time.


Well like I say much, much, much, much, much, much, much, much, much too often, you neglected to recolor the borders. If you don't do that, you're splices and recolors will look very unprofesional and bad. If you don't know what I'm talking about, take a close look at the sprite, see on moltress those borders that are brown. Those should have been made into a dark gray color. Now that's out of the way, I can move on.

 

Moltres other than the border issue is fine, I see nothing overly wrong with it. The female's beak and claws could be a tad dark, they seem a little too pale, darken up that second shade a tad.

 

THe splice firstly is too simple. A simple adition of its head and tail seems all you did. The head also isn't in there pefectly, could be a good bit better. Those border issues also remain in this one, and seem all over the place.

 

Ugg, the Starmie seems so bad. Not only because of the border, but the color choice with it. That green is a really pale, and doesn't go well with all those left over blue and purple bits. It might be better if it didn't have those.

 

Pay attention to those borders and take your time.

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

Guest
This topic is now closed to further replies.
×
×
  • Create New...